Shaanxi Nick Machinery
Equipment Co. LTD
TEL:86-29-86031588
Fax:86-29-86031588 Sitemap
Add:RongHao Industry Garden,Xi'an,Shaanxi,China
Email:sales@nkbaler.com
WhatsApp:008615021631102
Company News Your current location:Home >> Company News
  • China automatic waste paper baler manufacturers. Nick Machinery Factory takes products as the leader, capital as the link, and our factory culture as the core, covering various kinds of hydraulic equipment such as waste paper balers and waste plastic balers; mesh belt conveyors, chain conveyors, etc. device. How to repair the waste paper baler hydraulic pump of Nick Machinery Factory: Waste paper baler In our normal use, it is forbidden to disassemble the hydraulic pump. The hydraulic fluid used in the hydraulic system of the hydraulic baler is very compressible. Under normal circumstances, its influence is negligible, so even if the hydraulic baler system contains a small amount of air, the impact on the hydraulic baler is very large. of. The air dissolved in the oil will escape from the oil when the pressure is low, resulting in gas saturation and cavitation. In the high pressure zone, these bubbles are quickly crushed under the action of pressure oil, which is compressed abruptly, causing noise in the hydraulic baler system. At the same time, when the gas is suddenly compressed, a large amount of heat is released, causing local overheating and hydraulic pressure. The components and hydraulic oil are damaged. The high compressibility of the air also causes the actuator to creep, disrupt the smoothness of the work, and sometimes even cause vibration, which affects the normal operation of the hydraulic baler system. According to the different reasons why the air enters the hydraulic baler system, the following points should be noted in the use and maintenance. First, an exhaust valve should be installed on the upper part of the hydraulic baler to facilitate the discharge of the air in the cylinder and the system. The hydraulic baler adapts to changes in oil temperature and load that are greater than the use of a throttle valve. The parallel hydraulic cylinder synchronous circuit of the control valve using the flow rate has a simple structure and a low cost, so the application is relatively common.

    2. Try to prevent any pressure in the hydraulic baler system from being lower than atmospheric pressure. At the same time, use a particularly good sealing device. Replace the failure in time. Screw the pipe joint and each joint surface to clean the hydraulic pressure. The oil filter at the inlet of the baler tank.

    Third, in daily work, always check the height of the liquid oil surface in the hydraulic baler tank, and its height should be maintained on the oil mark scale line. At the lowest surface, the suction nozzle and the same oil pipe mouth should also be kept below the liquid level and must be separated by a partition. If there is an accident, please stop working immediately.as more information ,please visit us : www.nkbaler.com
  • With the increasing emphasis on environmental protection industry in China, the development of straw recovery industry will be gradually improved. On this basis, the level of mechanization of progress seems inevitable. As an important part of the packaging machinery industry, straw balers will in the future be diversified into mechanical functions, structural design standardization, modularization, intelligent control, and high-precision structure. The presentation of the straw baler, a mechanical device, is of great significance to China's packaging machinery industry, and the space for the development of this industry in China has been further explored. At the same time, consumers are satisfied with the increasing requirements for product packaging. Taking industry as an example, the use of the baler is indispensable, and its presentation is satisfied with the messy packaging requirements of the product. In addition, the use of this mechanical equipment is high efficiency, high quality, high environmental protection, and various types of low-cost requirements can be completed. In the future, the development of the baler function will be further broken and accustomed to the needs of the future.as more information ,please visit : www.nickbaler.com  
  • Sawdust Baler machine Shipping Indonesia and loading container by 2*40HQ .
  • To celebrate the 70th anniversary of the founding of China, we will be on holiday from September 30, 2019 to October 7, 2019, and work on October 8, 2019.

  • Holiday notice 2019-09-26
    To celebrate the 70th anniversary of the founding of New China, we will have a 7-day holiday, from October 1st to 7th for the holiday time, and officially go to work on October 8.
  • Many customers are aware of the straw granules and different sizes of granules when consulting the machine. In fact, the straw granule machine and the straw briquetting machine should belong to the straw granule machine. Why are they divided into two models? Of course, because the size of the particles is different, of course, the mold used is not the same. Let's talk about the different parts of the straw pellet machine and the straw briquetting machine.
    Straw granule machine, the mold cylinder type is generally five to six rows of small holes, and the size is from 350 to 580. There are various models, mainly pressing small cylindrical particles, which are generally used in daily biomass boilers, or Biomass burning appliances, because of the small size of the particles, can be formed whether it is straw or wood chips, of course, this also combines the specific material and mold compression ratio. The straw briquetting machine uses a block mold, generally consisting of 36 or 48 blocks, and can produce block biomass particles of different sizes such as 20*20, 30*30, etc., generally used for straw pressing, and can also be pressed. Wood chips, but according to the different raw materials, the mold length, material moisture, composition, reasonable allocation, this block particles, because of the larger, better flame resistance, biomass power plants use more.
    It can be understood from the above that the straw briquetting machine is different from the pellet machine. When the straw briquetting machine is used, the straw is mainly subjected to briquetting treatment, and the pellet machine is mainly made of straw into pellets. According to the needs of customers, using different products, the effect of production can make you more satisfied.
Shaanxi Nick Machinery Equipment Co. LTD
TEL:86-29-86031588
Fax:86-29-86031588 Sitemap
Add:RongHao Industry Garden,Xi'an,Shaanxi,China
Email:sales@nkbaler.com
WhatsApp:008615021631102
Copyright © 2018 NKBALER .rights reserved
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD